Советы рыболову зимой Советы рыболову весной Советы рыболову летом Советы рыболову осенью Общие 

Разделы

  Основы
  Поплавочная удочка
  Спиннинг
  Спиннинг-приманки
  Донная удочка
  Нахлыст
  Другие снасти
  Рыбы наших водоемов
  Семейства рыб
  Наука ихтиология
  Рыбацкая кухня
  Техника безопасности
  Первая помощь
  Видео
  Статьи о рыбалке
  Разное




Рубрики

  Отчеты о рыбалке
  Календарь рыболова
  Мастерская рыбака
  Вопрос - Ответ
  Стихи про рыбалку
  Болезни рыб
  Насадки
  Эхолоты
  GPS приемники
 

трос рулевого управления к лодочному мотору ямаха



Lowrance Transducer Installation Manual




Transducer location selection and installation are two of the most critical steps in sonar installation. To function properly the transducer must be in the water at all times, and in a location that has a smooth flow of water when the boat is moving.

lowrance transducer installation

Select a transducer location The primary aim is to stay clear of propeller and hull-generated turbulence, while mounting the transducer as close to the center of the vessel as possible. Avoid mounting within 3. Conventional clockwise propeller rotation 3.

lowrance transducer installation

Best mounting location - undisturbed water flow 5. Planing strake - avoid mounting behind here NOTE: Boats with strakes or ribs on the hull can create large amounts of turbulence at higher speeds. A good transducer location on these types of boats is between the ribs closest to the engine.

  • Афоризмы про рыбалку
  • Что такое вес лодки с полным оснащением
  • Талисманы для рыбаков
  • Микадо спиннинг кастинговый
  • If the transducer is not placed in a smooth flow of water, interference caused by bubbles and turbulence may show on-screen in the form of random lines or dots. Removing the transom slide mount The slide can be removed from the DSI transducer by depressing the release tab with a flathead screw- driver and sliding off the transom slide mount. S lide the transducer into the bracket and slide the bolt through the transducer bracket. H old the transducer assembly against the transom.

    lowrance transducer installation

    Look at the transducer from the side. C heck to see if the transducer will adjust so its face is parallel with the ground. Repeat this process until the transducer face is parallel to the ground.

    lowrance transducer installation

    Check that there is nothing on the other side of the mounting surface that may be damaged by drilling. Attach the transducer to the transom, using supplied stainless steel screws. If performance does not improve with tilting, try adjusting the height of the transducer relative to the transom of the boat. If the transducer is too high it may be seeing cavitation caused by the trailing edge of the transom. For shoot-thru-hull applications, many boat hulls have a flat keel pad that offers a good transducer mounting surface. Make sure the Skimmer transducer is oriented so the nose of the transducer is facing the bow front of the boat. P ress the transducer into the epoxy, turning it to force out any air bubbles from under the transducer face. Make sure there are no air pockets between the transducer and the hull. S top pressing when it bottoms out on the hull.

    Lowrance Transducers

    Apply pressure to hold the transducer in place while the epoxy sets. Allow the epoxy to set before moving the boat. W hen finished, the face of the transducer should be parallel with the hull with a minimum amount of epoxy between the hull and transducer. If the transducer has a built-in temp sensor, it will only show the temperature of the hull, not the water temp. Contact information Customer Service: This manual is divided into two. Make sure you read all the installation instructions before drilling holes in your vessel. Find out if the boat builder has a recommended installation location. Establish direction of rotation of the propeller s. W ith the boat traveling at cruising speed, watch the water flow behind the boat to find the. Summary of Contents for Lowrance Transducer Page 1 Transducer location selection and installation are two of the most critical steps in sonar installation. Page 3 Select a transducer location The primary aim is to stay clear of propeller and hull-generated turbulence, while mounting the transducer as close to the center of the vessel as possible. Page 5 Removing the transom slide mount The slide can be removed from the DSI transducer by depressing the release tab with a flathead screw- driver and sliding off the transom slide mount.

    Changing your lowrance transducer made easy

    Page 12 If performance does not improve with tilting, try adjusting the height of the transducer relative to the transom of the boat. Page 13 For shoot-thru-hull applications, many boat hulls have a flat keel pad that offers a good transducer mounting surface. Page 14 Part No. Contact Information Contact information Customer Service: Page 16 Visit our website: Comments to this Manuals Your Name. Enter text from picture: To print the manual completely, please, download it. Got it, continue to print..




  • Резиновый комбинезон для охоты и рыбалки
  • Mikatsu m5fhs купить в москве
  • На какие снасти можно ловить рыбу во время запрета на оке






  • Нравится сайт? Поделись с другом!